Getting Started

Breez Edge can be mounted on a wall using the backplate or placed on a table using the table stand (both included in the box).

Before finalizing the placement, it is recommended to first power up, register and test the device to ensure signals can easily reach the mini-split. 

For optimal placement and control:

• Make sure Breez Edge is within the line of sight of the mini-split. 
• To avoid deviated sensor readings, do not place Breez Edge where it may be exposed to excessive sunlight or other heat sources.

Special Note: It is strongly advised that whenever there is a need to use the remote control for AC/heat pump, point it towards Breez Edge while performing any action. This way, your AC/heat pump and Cielo Home app will always be in sync.

Powering Up

Breez Edge can be powered up using the 5V adapter (always use the provided power adapter and USB cable for optimal results).

Please DO NOT use any other voltage level to power up Breez Edge. Please choose ONLY ONE power-up option, i.e., either 5V OR 24V.

Powering Up Using 24V Connection

Step 1: Switch off the power by using the circuit breaker. This is very important for your safety.
Step 2: Find a point where 24V is available (in case of non-availability of 24V point, you can use an external transformer). Ensure that chosen point is also within the line of sight of the AC

Note: Please DO NOT use any other voltage level to power up Breez Edge

Step 3: Take out the wires through the hole in the middle of the backplate. Screw in the backplate using the provided pair of drywall anchors and screws.

Step 4: Cielo Breez Edge has two terminals marked as Rc and C on its backplate. Insert red wire into Rc and black wire into C from the side (press the terminal block buttons for ease of insertion).
Step 5: Align Breez Edge with the backplate and press gently to fix it properly

The installation is complete. Please switch on power from the circuit breaker

Prior to App Installation

For Phone:

• Make sure your smartphone’s Bluetooth is turned ON.
• Ensure your smartphone’s Wi-Fi is turned on.
• Make sure your smartphone has internet access.

For Wi-Fi Router:

• Make sure the Wi-Fi router has a working internet connection.
• Make sure there is no proxy server or authentication server configured on the internet connection.
• Make sure there is no captive portal on the Wi-Fi router.

Note: Make sure IP isolation or client isolation is turned OFF on your Wi-Fi router.

App Installation & Registration

Help your customer install the ‘Cielo Home’ app from the App Store/Play Store. They can either log in with an existing account or create a new one using the sign-up option.

Device Registration

 Device registration process connects Breez Edge to the home Wi-Fi network through the Cielo Home app.

Note for iOS users:

• For iOS 13.0 & above, location permission is required to complete the registration process. You may disable it later. 

Note for Android users:

• For Android OS 8.1 and above, location permission is required to complete the registration process. You may disable it later.  

Open the Cielo Home app, tap ‘Add Device’ on the home screen, and select Breez Edge from the list of devices.

Step 1: Tap on 'Continue'.

Step 2: Allow required permissions and tap 'Continue'.

Step 3: Tap ‘Connect’ to proceed.

Step 4: Name the device and tap 'continue.'

Step 5: Tap on 'Scan Wi-Fi networks.' Choose the Wi-Fi network.

Step 6: After Wi-Fi configuration, tap on 'Next' to start auto remote detection. 

Step 7: Point the remote at Breez Edge and press the remote’s ‘Power button’ once. It will start the configuration process.

Step 8: The remote is now paired with Breez Edge. Tap on ‘Done’.

Step 9: To verify if your remote is configured correctly, tap on 'Test your remote.'

Step 10: Tap ‘Continue.'

Step 11: Tap on the power icon as shown.

Step 12: If your AC responds correctly, tap 'Yes, it's working fine.' If it doesn't, select 'Let's try again.'

Step 13: You can add your address at this step or do it later. 

Registration process is complete. 

Home Screen

Home screen shows the real-time status of all the Cielo devices. A registered Cielo device can show either of the 2 statuses outlined in circles:

1 - Green - Device is online.

2 - Red - Device is offline.

• Ensure your phone/device is connected to a working internet connection.
• Refresh the home screen by swiping downwards (Pull-to-refresh).

Configuring the Right Remote Control for the AC

Breez Edge auto-detects the relevant remote control for your AC during the registration process. You can also configure your AC remote manually.

For manual selection, follow these steps:

Screen A: Go to settings by tapping the ‘Settings’ icon on the control screen

Screen B: Select ‘Change Appliance’.

Screen C: Select ‘Manual Configuration’.

Screen D: Select the ‘Manufacturer’ & ‘Remote Model’ from the drop-down list and tap ‘Done.’

Quick Tip: Remote control model number is usually found on the back side of the remote control.

Cielo Home App Control Screen

Breez Edge Control Screen

Mode: 
Indicates the current mode of the AC. Tap on the mode icon to select the preferred mode.

Indoor Humidity
Displays current humidity level in the room.

Menu
Allows to set schedules, activate Comfy Max, adjust device preferences, and much more.

Indoor Temperature

Displays the current room temperature.

Setpoint
Desired temperature the AC aims to achieve. 

Weather
Shows the current weather and weekly forecast.
Note: In case of an internet outage, Breez Edge saves 72 hours of weather data to keep making weather-based decisions, ensuring uninterrupted home comfort.

Presets
Gives quick access to Presets - Home, Away, Pets, and Sleep.